Ram 1500 Hitch Receiver Fitment: Avoid Costly Mismatches

by | Nov 21, 2026 | Ram Accessories | 0 comments

Choosing a Ram 1500 hitch receiver sounds easy until you crawl under the truck and find a ball hole where you expected a 2-inch square opening. A part that fits a 2018 truck won’t fit a 2019 truck, a “Class IV” label can sit on a 6,000-pound hitch, and plenty of listings say “fits Ram 1500” without saying which one.

Affiliate Disclosure: As an Amazon Associate, RAM Care Pro earns from qualifying purchases. If you buy through links in this article, we may earn a commission at no extra cost to you.

This guide walks through what your truck probably has now, what the hitch classes really mean, and four receivers worth comparing. It is research-based: ratings and fitment come from manufacturer and retailer listings, and we haven’t installed these parts ourselves. Treat every fitment note as a starting point, then confirm it against your VIN and the current listing.

Ram 1500 Hitch Receiver Fitment: Start With What Your Truck Has

Two different trucks wear the Ram 1500 badge for 2019 through 2024. The redesigned “new body” truck (often called the DT) and the older body style sold as the Ram 1500 Classic. Hitches are not interchangeable between them, and etrailer’s technicians have said so directly for 2022, a year when both were on sale. If you’re unsure which you own, our Ram 1500 year guide breaks down the generations.

Next, look at the back bumper. According to etrailer’s experts, a 2019 Ram 1500 comes standard with a Class III bumper-mount hitch, which means a ball hole in the bumper step rather than a receiver. A frame-mounted Class IV receiver is separate equipment. In one 5thGenRams thread, a 2019 buyer who believed his truck had a tow package turned out to have no receiver, and replies pointed out that the trailer plug is there either way. That’s an owner account, not a Ram specification, but it shows why a quick look under the bumper matters.

  • Ball hole in the bumper step: you likely have the Class III bumper setup.
  • 2-inch square opening under the bumper: you already have a receiver. Read its markings before replacing it.
  • Older body style: check whether the truck came with a factory receiver, since several aftermarket hitches are listed only for trucks without one.

For a broader walkthrough of ball mounts, wiring, and tongue weight, see our Ram 1500 trailer hitch guide. This article focuses on choosing the receiver itself.

Class III, IV, and V: What the Ratings Actually Tell You

The class label is a rough category, not a capacity. Look at how different the numbers are among the products below:

  • CURT 13419 is labeled Class III and rated 6,000 lb gross trailer weight with 600 lb tongue weight.
  • Draw-Tite 76328 is labeled Class IV, yet Draw-Tite rates it at the same 6,000 lb and 600 lb.
  • Mopar’s factory-style Class IV receiver is listed at 12,750 lb with 1,275 lb tongue weight.
  • CURT 15005 is labeled Class V and rated 15,000 lb and 1,700 lb.

Two limits sit above all of that. First, a hitch rating never raises your truck’s rating. CURT’s own notes say hitch ratings are limited to the vehicle manufacturer’s stated capacities, and you should never exceed the lowest-rated component in the setup. Check Ram’s towing capacity guide and our Ram towing guide for the number that applies to your configuration.

Second, tongue weight should land around 10 to 15 percent of the loaded trailer, according to Mopar. Ram’s towing charts also recommend a weight-distributing hitch for trailers over 5,000 lb. Not every receiver allows one: Draw-Tite states that no weight-distribution kits can be used with the 76328.

Four Ram 1500 Hitch Receivers Compared

The table lists manufacturer and retailer figures only. Prices, ratings, and stock change often, so check the current listing instead of trusting a number printed here.

Swipe or scroll horizontally to compare all product details.

ProductBest useRated (trailer / tongue)Listed fitment (verify)Main drawbackCheck listing
CURT 13419 Class 3New-body trucks with the factory Class III tow bumper6,000 lb / 600 lb2019 and newer Ram 1500 with Class III tow bumperLowest ratings of the groupView on Amazon
Draw-Tite 76328 Class 4Frame-mounted receiver for light to moderate trailers6,000 lb / 600 lbNew body style; Draw-Tite lists 2019–2026, Amazon title says 2019–2022No weight-distribution kits allowedView on Amazon
CURT 15005 Class 5 Xtra DutyHeavier trailers, weight distribution15,000 lb / 1,700 lb (17,000 lb / 1,700 lb with WD)2019 and newer; retailers disagree on the last yearHeavy, longer install, truck still sets the limitView on Amazon
CURT 13333 Class 32011–2018 trucks and 2019–2024 Classic without a factory receiver6,000 lb / 600 lb (10,000 lb / 1,000 lb with WD)Older body style onlyWill not fit new-body trucksView on Amazon
Mopar 82215222AD Class IV (OEM reference)Factory-matching replacement12,750 lb / 1,275 lb2019–2026 Ram 1500Not verified on Amazon; dealer or parts-store purchaseMopar listing

Product Profiles: Who Each Receiver Suits

CURT 13419 Class 3: The Bumper-Hole Upgrade

Best for: new-body trucks that came with the ball-hole tow bumper and tow small trailers, bike racks, or cargo carriers.

etrailer’s experts describe it as the receiver for trucks with the Class III tow bumper, bolting to the bumper beam and frame brace. CURT lists it as no-drilling, and one retailer estimates 30 to 60 minutes. Drawback: 600 lb of tongue weight leaves little room for a loaded travel trailer. Check on the listing: your truck has the Class III tow bumper, and the seller and brand are CURT. Search results for “13419” also show third-party products reusing the number, so confirm you’re opening the CURT listing. See the CURT 13419 on Amazon.

Draw-Tite 76328 Class 4: Frame-Mounted, Modest Ratings

Best for: owners who want a frame-attached receiver for utility trailers, small boats, or a hitch cargo carrier.

Draw-Tite lists a 15-minute install for 2019 through 2026 new-body trucks, though two retailers say drilling is required, so read the instructions before you plan your afternoon. Drawback: the Class IV label suggests more capacity than the 6,000 lb and 600 lb ratings deliver, and weight-distribution hitches are off the table. Check on the listing: the Amazon title references 2019–2022, while Draw-Tite’s page covers a wider range, so confirm your year with the Amazon fit tool. Check the Draw-Tite 76328 listing.

CURT 15005 Class 5 Xtra Duty: Built for Weight

Best for: frequent towing of heavier trailers, especially with a weight-distribution hitch.

CURT rates it at 15,000 lb and 1,700 lb, with 17,000 lb and 1,700 lb for weight distribution. That is far above Ram’s published figures for the 1500, which our towing guide puts at up to 11,610 lb for 2026, so the truck remains the limiting factor. Drawback: retailers list it at roughly 70 to 85 lb, installation is listed at 60 to 90 minutes, and one owner reported about three hours including removal of the old Class III hitch. Check on the listing: the last compatible model year and whether the instructions replace your existing hitch. View the CURT 15005 on Amazon.

CURT 13333 Class 3: For the Older Body Style

Best for: 2011–2018 Ram 1500 trucks and 2019–2024 Classic models without a factory receiver.

The rating is 6,000 lb and 600 lb, or 10,000 lb and 1,000 lb with weight distribution. etrailer’s technicians say it installs using the bumper hole plus two additional holes at the rear. Drawback: it is not a new-body part, and listings generally exclude trucks with a factory receiver. Check on the listing: your exact year and body style. See the CURT 13333 on Amazon.

Mopar Class IV: The Factory Reference Point

Mopar lists a Class IV receiver for 2019–2026 trucks at 12,750 lb and 1,275 lb, described as matching the production hitch. Ratings for the factory receiver appear differently across sources and years, and our trailer hitch guide cites a lower figure from the 2026 owner’s manual. Use the lower number that applies to your truck.

Installation, Wiring, and Upkeep

Most of these receivers are advertised as vehicle-specific bolt-ons, but “no drilling” is not the same as “no effort.” Expect to need a socket set and a torque wrench, and follow the torque values for your exact part. After the first few trips, recheck the bolts. If you’re comfortable with Class V weight, plan for a second person.

A receiver doesn’t include trailer wiring or a brake controller. Owners on 5thGenRams note that adding a brake controller can be a bigger job than the hitch. Wiring differs by year and equipment, so use our trailer wiring walkthrough as background only, and verify pin assignments for your truck.

If the rear squats under tongue weight, an air spring kit may help comfort, but it doesn’t change any rating. Our Ram 1500 air bag guide explains the difference.

Common Buyer Mistakes

  • Ordering by “Ram 1500” alone. Body style and model year decide the part. Our Ram 1500 accessories guide makes the same point for add-ons.
  • Trusting the class label. Compare the trailer and tongue weight numbers, not the word “Class IV.”
  • Pairing a hitch with an aftermarket bumper. etrailer’s experts say custom-fit hitches are designed for factory bumpers; compatibility with aftermarket bumpers isn’t something they can promise.
  • Assuming a bigger receiver upgrades the truck. It doesn’t.
  • Ignoring ball-mount height. One 5thGenRams owner found the factory bumper setup too tall for a car trailer and went to a frame hitch so a drop receiver would fit.

Key Facts at a Glance

  • New-body and Classic trucks use different hitches.
  • Many new-body trucks leave the factory with a bumper ball hole, not a receiver.
  • Class III, IV, and V labels don’t predict ratings. Read the trailer and tongue weights.
  • The truck’s published limits always apply, whatever the hitch says.
  • Weight-distribution compatibility varies by hitch.
  • A receiver doesn’t include wiring or brake control.
  • Confirm fitment against your VIN and the current listing before ordering.

Ram 1500 Hitch Receiver FAQ

Does every 2019 and newer Ram 1500 have a 2-inch receiver?

No. etrailer’s experts say the 2019 truck comes standard with a Class III bumper-mount hitch. Check the back of your own truck and your build information.

Can I add a receiver to a truck with the ball hole?

Yes. CURT’s 13419 is listed for trucks with the Class III tow bumper, rated at 6,000 lb and 600 lb.

Does a Class V receiver increase my towing capacity?

No. The truck’s own ratings still apply, and CURT states that hitch ratings are limited to the vehicle manufacturer’s capacities.

Do I have to remove the factory hitch first?

Reports for Class V designs describe replacing the factory unit. One owner removed an old Class III hitch before installing the 15005, and etrailer says a Draw-Tite Class V replaces the factory hitch and needs exhaust heat shield tabs flattened. Follow the instructions for the product you buy.

Will it fit with an aftermarket rear bumper?

Don’t assume so. Custom-fit hitches are designed around factory bumpers, so ask the bumper or hitch manufacturer.

Which Receiver Fits Which Owner?

  • Small trailer, bike rack, or cargo carrier on a new-body truck with a ball hole: the CURT 13419 is the most direct match.
  • Frame-mounted receiver, no weight distribution: consider the Draw-Tite 76328, after confirming your year.
  • Regular heavy towing with weight distribution: the CURT 15005, provided your truck’s own ratings support the load.
  • 2011–2018 or Classic without a receiver: the CURT 13333.
  • Want a factory match: ask a Ram dealer about Mopar’s 82215222AD.

If your truck already has a factory receiver rated for your trailer, you may not need to buy anything. For heavier setups, our RV towing essentials guide covers brakes, mirrors, and pre-trip checks.

Sources and further reading:

Written by

David is the writer behind MyRamCare. He researches RAM truck maintenance, troubleshooting, repair-related topics, accessories, and everyday ownership questions to help readers understand automotive information in clear, practical language. His articles draw on available manufacturer information, vehicle owner's manuals, and other relevant automotive references. David is an independent automotive information writer, not a certified mechanic or professional repair technician. His articles are intended for general educational purposes and should not replace vehicle-specific manufacturer instructions, professional diagnosis, or qualified repair services.

Related Posts

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *